Which Grade of Treated Timber Should Go Under My Deck?

Last updated: November 2026

The posts, joists and frame need Use Class 4 (UC4) treated timber. Use Class 3 (UC3) is for timber above the ground, such as the boards. Ask for the class in writing before the timber is ordered.

A deck can look fine on top while the timber holding it up is failing. The grade of treated timber under the boards is easy to never ask about. This guide is for homeowners in Bournemouth, Poole and Christchurch getting quotes.

What do UC3 and UC4 mean?

They are British Standard use classes, which rate how wet a piece of timber will get once it is in place. UC3 is for outdoor timber that is not in the ground. UC4 is for timber in contact with the ground or fresh water.

The Wood Protection Association sorts timber into five use classes. Its table lists “landscaping and decking timbers not in contact with the ground” under Use Class 3, and “fence and deck post” under Use Class 4. The two can look the same on the yard shelf, but the amount of preservative driven into them is different.

Which parts of a deck need UC4?

The posts, the joists and the rest of the frame. The boards above can be a lower class if they are clear of the ground.

On my builds the ground-contact frame is C24 strength-graded, Use Class 4 treated timber, whichever board goes on top. My clay-soil guide cites the Association’s buyer’s guide placing decking posts, joists and sub-structures in Use Class 4. For anything borderline, the Association’s advice is to move up a class, from UC3 to UC4.

Ground across Poole and Bournemouth changes over short distances, from thin, sandy heathland soil around places like Canford Heath to clay-rich ground elsewhere, so two gardens in the same road can dig differently. My guide to building stable decking on clay soil covers how to check yours and what that does to the footings.

What happens if the wrong grade goes in the ground?

It rots from underneath. The Association says to never use wood treated for an indoor class in an external one, and that ground contact needs Use Class 4 levels of protection, or service life and structural safety suffer.

The Association also notes that the class a component needs can change if the timber ends up wetter than planned, for example through design faults or poor workmanship. That is why I would rather you asked about the hidden timber than the visible boards.

What about the cut ends?

Treat them. When timber is cross cut, notched or drilled on site, it exposes wood the preservative did not reach.

The Association tells installers to keep a can of end grain preservative to seal that untreated wood. On a deck it is a small job, and it is easy to skip if nobody is checking.

What is BS 8417 and what does the service life figure mean?

BS 8417 is the British Standard for how preservative is applied to timber. It sets the level of treatment by use class and by the service life asked for: 15, 30 or 60 years.

For external applications like fencing and decking, the Association says 15 years is the default. That is a treatment specification for the timber, not a promise about any particular deck. How long a deck lasts also depends on the design, the ground and the upkeep.

Fixings are a separate question, and a bigger one near the sea. See which decking screws last near the sea.

What should I ask for in a quote?

Ask which use class the posts and frame are, and ask for it in writing. The Association’s own advice is to state the use class and BS 8417 on the order, then ask for the delivery note or a treatment certificate.

A straight answer tells you more about a job than most of the sales talk. My buyer’s guide to hiring a decking installer has the rest of the questions worth asking, and what decides the price of a new deck explains why the hidden timber shows up in a quote. If you are weighing materials, the composite vs timber guide covers the boards.

Treated Timber FAQs

What is the difference between UC3 and UC4 timber?

UC3 is treated for timber exposed to the weather but out of the ground. UC4 is treated for timber in contact with the ground or fresh water. UC4 carries more preservative.

Can UC3 timber be used for deck boards?

Yes. The Wood Protection Association lists decking timbers not in contact with the ground under UC3. The posts, joists and frame underneath are UC4 on my builds.

What should I do when I cut treated timber on site?

Seal the cut end with end grain preservative. A saw cut, notch or drilled hole exposes wood the preservative never reached.

How can I check what timber a contractor is using?

Ask for the use class and the BS 8417 treatment in writing, then ask for the delivery note or a treatment certificate once the timber arrives.

Sources

Get a Free Quote That Names the Timber

I will walk the garden with you and put the timber grade in writing.

Get a Free Quote

Or call me direct on 01202 144040